MAC MTH-80 8" Chef's Knife w/ Dimples

You looking to find the "MAC MTH-80 8" Chef's Knife w/ Dimples" Good news! You can purchase MAC MTH-80 8" Chef's Knife w/ Dimples with secure price and compare to view update price on this product. And deals on this product is available only for limited time.

Price: $144.94    

Product Feature

• Mighty Chef 8-1/2" - Chef Knife w/ Dimples.
• All-purpose, glides through cuts.
• Tungsten Alloy

MAC MTH-80 8" Chef's Knife w/ Dimples Review

I have the MTH-80 Mighty Chef Knife with Dimples. It came extremely sharp out of the box and stays that way. I have only honed it lightly a few times with a borosilicate glass steel after smacking the cutting block with my poor style. This thing rocks. With my Chicago Cutlery knives the same abuse would put very slight dents in the edge barely visible as a glint of light under a bright light and I could feel the loss of sharpness after a few cuts. The edge on the MAC is so acute and fine that I didn't want to take a change and loose anything with a steel (which is not recommended) or even a 1200 grit ceramic steel (which is recommended) so I went with the borosilicate glass rod which is finer. It still cut fine and I didn't notice a difference but I could feel a slight change in the razor edge. The rod brought the edge back to new or better every time. This thing is tougher and holds an edge better then good non-stainless carbon steel knives I have used.

This knife is thinner, lighter, the steel is harder, it holds a edge better, and is more nimble then a comparable Western knife like a Wusthof or Henckel. Some may not like that. I do, although you don't want to use it like a clever and you probably could get away with that with Wusthof or Henckel. They both have their place but I like the MAC for my style of use.

Some have recommended the Forschners from Victorinox . I tried the paring set for $10 and the serrated parer or sandwich knife. They are sharp but not as sharp as the MAC's. Also, the Fibrox handle, at least on the paring knives, is so small it gets lost in my hand. I cut a hard crusty French bread with the serrated knife and the points were showing signs of blunting or rolling over. A little steeling brought that back but I don't think the Forchners are all they are cracked up to be. I would agree they are probably the best knives for the money (for example those 3 knives for $10). They are pretty amazing for the price but the MAC's are about the best cutting experience you can buy. You can pay more for something to look at but the MAC's seem to perform the best.

I am looking foward to getting the MAC PK-30 paring knife and the SB-105 bread knife to replace some of my other inferior knives. Those 3 (plus maybe a Santoku) are really all I need.

The MAC's are not real fancy with silver inlays or high polish or anything but it cuts like a razor and stays that way better then any of my other knives. The fit and finish is good too.

The steel is very similar to the Globals but I don't like the feel of the Globals and I think the handles on the Globals would get slippery when wet or greasy. Also, the MAC came very sharp out of the box. They say Globals are that way too but some I looked at in the store had a burr on the edge and need some attention before use.

To keep it sharp, I would recommend anyone with a knife like this, the Shun's or the Global's either get the MAC or Idahone ceramic steel or a Idahone 2 or 4 stick sharpener. Amazon has them listed a "not available" but you can get one at Sonoma Cutlery. These are easy to use and you get the correct angle just by holding the knife vertical and stroking. the 4 stick model also has a 15 and 20 degree angle for the sticks. I would use the 15 degree slots.

I don't usually come back and rate something I bought but I did a lot of research and after using the knife through Thanksgiving I have become passionate about it and MAC knives in general and want to share them with everyone else. They are kind of a secret and fairly hard to come buy. Also MAC's are not sold in sets and you may not even be able to build a set from one style of MAC (like Classic, Professional, Superior, etc). You may have to mix styles. This is apparently in Japanese tradition even though these are Japanese made western style knives. What you get with most Japanese western knives is Japanese steel and Japanese style sharpening and profile. To make a knife this thin work with such a fine edge you have to have harder steel then western manufactures generally use or the blade would quickly dull from use.

For other references check out Cooking for Engineering Chef knife test.
(do a Google search on it) and also see Knife Forums. For KF do a Google search with the knife you want to explore with the KF in the search. For example search " best chef knife site: and put knifeforum. com ". Leave off the quotes and spaces. Sorry if that was a little cryptic. It looks like Amazon won't let me put the URL's here.

Also for knife sharpening see: Chad Wards directions in knive forums.

Most of the consumer Reviews tell that the "MAC MTH-80 8" Chef's Knife w/ Dimples" are high quality item. You can read each testimony from consumers to find out cons and pros from MAC MTH-80 8" Chef's Knife w/ Dimples ...